Ravinte Cabinet Door & Drawer Hardware Installation Template Kit Include Drill Bit

Add to wishlistAdded to wishlistRemoved from wishlist 0
9.6
Expert ScoreRead review
9.6Expert Score
Overall BVR Rating
Total Reviews:8435
Ravinte Cabinet Door & Drawer Hardware Installation Template Kit Include Drill Bit
PROS
  • 63 REVIEWS DRILL BIT
  • 104 REVIEWS EASY TO USE
  • 24 REVIEWS MUCH EASIER
  • 23 REVIEWS HIGHLY RECOMMEND
  • 18 REVIEWS WORTH THE MONEY
  • 59 REVIEWS CABINET HARDWARE
  • 23 REVIEWS INCLUDED DRILL
  • 12 REVIEWS TIME SAVER
  • 24 REVIEWS WORKED PERFECTLY
  • 38 REVIEWS GREAT TOOL
  • 111 REVIEWS INSTALLING CABINET
  • 14 REVIEWS MAKE SURE
  • 23 REVIEWS MADE THE JOB
  • 19 REVIEWS SUPER EASY
  • 38 REVIEWS DRAWER PULLS
  • 69 REVIEWS MADE INSTALLING
  • 53 REVIEWS CABINET PULLS
  • 41 REVIEWS DRAWER TEMPLATE
  • 26 REVIEWS WORKED WELL
  • 5 REVIEWS SAVED ME A LOT
SKU: B083QXDV3R Category: Tag:

WORKS FOR DRAWER & DOOR: Knob and Pulls with 3″ (76mm), 3-3/4″ (96mm), 5-” (128mm) hole center. If you need other size, please refer to ASIN (B09J53C71N).

Top Positive Review


I decided to take a chance on a low cost option for my cabinet/door handles ( $1.36 per ) and decided to buy the extra template because i knew it would be easier. Now they have good spacing on the template but it didn’t line up dead center on my doors. That’s okay because it was close enough and you wouldn’t be able to tell. The drawer template was super easy to use with the notch on top to line up my middle and the door template has guides to get you aligned with the door corner. The drill bit that came with was good as a punch to start the hole but the drill was not cut correctly i think so i wasn’t able to actually drill anything with it.

The drill bit does not warrant a lesser rating.

If/when i move and need handle updates I’ll be looking at Ravinte again.

Top Critical Review


I can’t give it a horrible review because I don’t know how any one could make a jig that would fit every situation. The holes were roughly an 1/8″ off for the corner cabinet jig so I taped a piece of cardboard on the sides and bottom to make it work. The drawer jig worked fine. Some advice: use painters tape on your cabinets to mark the holes, double check your measurements every time, Drill a pilot hole before you drill the 3/16 hole, leave the tape on when you drill, and pre drill the back side before you drill through from the front side.

Customer Questions & Answers


What are the dimensions of the drawer template?
Answer:

Hello,

The small template suit for 3inch, 3.75inch and 5inch hole center.

I hope it could help.
??

Will this work with 76 mm kitchen cabinet handles?
Answer: Yes, I used it with a hole spacing that was 76mm or 3″ and the handle length was 4 1/2 ” it should work.

Will this work on 96 mm kitchen cabinet handles?
Answer: Yes it will. There are marks for 3??, 96 and 128mm. There are slots for lesser measurements as well. These are handy and I didn??t have to make my own jig. Recommend.

Is there a setting for 5 1/2 inch hardware?
Answer: Only 3 and 3-1/2; and 96 and 128 mm. Hope this helps.

Can I order a few singles of this handle?
Answer: Not sure. I did all my new cabinets, and they look great!

User Reviews

0.0 out of 5
0
0
0
0
0
Write a review

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Amazon Hardware Products Reviews
Logo
Enable registration in settings - general
Shopping cart